D Which Command Is Used to Configure Ipv6 Static Routes

Routerconfig ipv6 route FE80020232 serail 01 201 B. Before configuring the device with a static IPv6 route you must enable the forwarding of IPv6 packets using the ipv6 unicast-routing global configuration command enable IPv6 on at least one interface and configure an IPv6 address on that interface.

15 6 1 Packet Tracer Configure Ipv4 And Ipv6 Static And Default Routes Instructions Answer

Before configuring static routes we must configure the router to forward IPv6 packets.

. Ipv6 unicast-routing Enter this command on each router. Configure an IPv6 recursive static route to. To configure IPv6 on a Cisco routers you need to do two things.

Enter this command on each router. Configure an IPv6 recursive static route to. Before configuring static routes we must configure the router to forward IPv6 packets.

Configure IPv6 Static and Default Routes. Enter this command on each router. Configure recursive static routes on R1.

Configure recursive static routes on R1. Configure IPv6 Static and Default Routes Step 1. Configure a directly attached and a fully specified static route on R2.

Nicocisco replied 2 months ago. Which command accomplishes this. A directly connected static route is typically used with a point-to-point serial interface.

R3 will be used as our main path to reach this address. Configure a directly attached and a fully specified static route on R2. Configure an IPv6 recursive static route to every network not directly connected to R1.

Enable IPv6 routing on all routers. To configure a directly attached IPv6 static route use the following command format. Configure a fully specific route from R2 to the R3 LAN.

Configure recursive static routes on R1. Creates a static route configured to send all packets to a next-hop address of 2001db8c1822. Before configuring static routes we must configure the router to forward IPv6 packets Which command accomplishes this.

Configure a fully specific route from R2 to the R3 LAN. This command globally enables IPv6 and must be the first command executed on the router. Enter this command on each router.

Restrictions for IPv6 Routing. Routerconf t Enter configuration commands one per line. Enable IPv6 routing on all routers.

In a fully specified IPv6 static route both the exit interface and the next-hop IPv6 address are specified. Ipv6 unicast-routing Enter this command on each router. Router config ipv6 route Recursive IPv6 Static Route A recursive static route is created when specifying the next-hop IP address.

Lets look at it from Headquarters or HQs perspective right now. The only real difference is that we are configuring the static routing for IP version 6 so our command will start out differently. For example lets do an IPv6 static route configuration example with 2001ABC32 network and 2001ABC11112222.

Ipv6 route 2001DB81164 Serial000. Router configipv6 route. Configure recursive static routes on R1.

For example if you use the following commands to create two static routes for network 30008 the route will place the first route to the routing table. Ip route 30000 255000 20002 10 ip route 30000 255000 40002 20. Enable IPv6 routing on all routers.

Lab Configuring IPv6 Static and Default Routes. Configure recursive static routes on R1. Configure IPv6 Static and Default Routes Step 1.

Austin configipv6 route 2001db8c18364 fastethernet 00. Ip route 00000 interface next-hop. Austin configipv6 route 2001db8c18364 2001db8c182264.

Configure a directly attached static route from R2 to the R1 LAN. 2017 Cisco andor its affiliates. Enable IPv6 routing on all routers.

Router config ipv6 route 2001ABC32 2001ABC111122221 IPv6 Default Route Configuration on Cisco IOS The Default Route is a type of static routing. If the first route fails the router automatically adds the second route to the routing table. Which command can you enter to configure an IPV6 floating static route.

Ipv6 route 00000 interface next-hop. Router configip route destination_network subnet_mask default_gateway administrative_distance permanent OR Router config ip route destination_network subnet_mask interface_to_exit administrative_distance permanent. To do this configuration we can use the below command.

There should be no surprises here with our static routing configuration. Routerconfig ipv6 route FE80020232 serail 01 1. Packet Tracer v601 only checks for directly attached and recursive static routes.

Routerconfig ipv6 route static resolve default D. Ipv6 route default interface next-hop. Enable IPv6 routing on a Cisco router using the ipv6 unicast-routing global configuration command.

R1configipv6 route 2001DB8232364 2001DB813133. Routerconfig ipv6 route0 serail01 C. There is a situation in IPv6 when a fully specified static route must be used.

How to configure Static Routes Static Route can be configured by the following IOS commands. Which command accomplishes this. Configure IPv6 Static and Default Routes Step 1.

Ipv6 route 2001DB81164 Serial000. To configure a directly attached IPv6 static route use the following command format. Configure the IPv6 global unicast address on an interface using the ipv6 address address.

Configure an IPv6 recursive static route to every network not directly connected to R1. Which command is used to configure an IPv6 static default route. R3 is added to our topology and I configured the same loopback address 2001DB8232323128 on both routers.

For example here we create a static route to R3 through R2 and set the Administrative Distance to 1. If the IPv6 static route uses an IPv6 link-local address as the next-hop address use a. Heres the static route that is used to use R3 as the primary path.

When the link is down we want to use R2. Before configuring static routes we must configure the router to forward IPv6 packets Which command accomplishes this. Configure a directly attached static route from R2 to the R1 LAN.

XXXXX IPv6 prefix vrf IPv6 Routing table Router configipv6 route 2001DB80364. 1 next hop adres. Creates a directly attached static route configured to send packets out interface fastethernet 00.

Configure an IPv6 recursive static route to. Packet Tracer v601 only checks for directly attached and recursive static routes. Ipv6 route 0 interface next-hop5.

Before configuring static routes we must configure the router to forward IPv6 packets Which command accomplishes this.

2 2 4 4 Packet Tracer Configuring Ipv6 Static And Default Routes Instructions Answers

1 1 3 Lab Troubleshoot Ipv4 And Ipv6 Static Routing Answers Itexam24

2 2 4 4 Packet Tracer Configuring Ipv6 Static And Default Routes Ccna V7 Answers